1 copyright ? 2010, everlight all ri ghts reserved. release date : jan . 0 6 .201 7 . issue no: dir - 0001387 rev.2 www.everlight.com technical data sheet chip infrared led with right angle lens EAISV3024A1 features ? small double - end package ? low forward voltage ? good spectral matching to si photo detector ? package in 8mm tape on 7 diameter reel. ? pb free ? the product itself will remain within rohs compliant version. ? compliance with eu reach. ? compliance halogen free .(br <900 ppm ,cl <900 ppm , br+cl < 1500 ppm) description ? EAISV3024A1 is an infrar ed emitting diode in miniature smd package which is molded in a water clear plastic with spherical top view lens. the device is spectrally matched with silicon photodiode and phototransistor . applications ? infrared applied system device selection guide device no. chip material lens color EAISV3024A1 gaalas water clear
datasheet eaisv 3024 a 1 2 copyright ? 2010, everlight all ri ghts reserved. release date : jan . 0 6 .201 7 . issue no: dir - 0001387 rev.2 www.eve rlight.com package dimensions notes: 1.all dimensions are in millimeters 2.tolerances unless dimensions 0.1mm absolute maximum ratings (ta=25 parameter symbol rating unit continuous forward current i f 65 ma peak forward current *1 i fp 400 m a reverse voltage v r 5 v operating temperature t opr - 40 ~ +85 stg - 40 ~ + 100 sol 260 d 1 00 mw notes: *1:i fp conditions -- pulse width Q s and duty Q Q
datasheet eaisv 3024 a 1 3 copyright ? 2010, everlight all ri ghts reserved. release date : jan . 0 6 .201 7 . issue no: dir - 0001387 rev.2 www.eve rlight.com electro - optical characteristics (ta=25 ) parameter symbol min. typ. max. unit condition radiant intensity i e 5.0 8.5 -- mw /sr i f =20ma peak wavelength p 920 940 960 nm i f =20ma spectral bandwidth ? -- 3 5 -- nm i f =20ma forward voltage v f 1.15 1.3 0 1. 6 0 v i f =20ma -- 1. 70 2 .10 i f = 100 ma pulse width Q 100 s ,duty Q 1% reverse current i r - - -- 10 a v r =5v view angle 2 1/2 -- 50 -- deg i f =20ma
datasheet eaisv 3024 a 1 4 copyright ? 2010, everlight all ri ghts reserved. release date : jan . 0 6 .201 7 . issue no: dir - 0001387 rev.2 www.eve rlight.com typical electrical/optical/characteristics curves forward current vs. ambient temperature spectral distribution relative intensity vs. forward current forward c urrent vs. forward voltage 0 20 40 60 80 100 0 20 40 60 80 100 t amb - ambient temperature (c) i f - forward current (ma) 0 5 10 15 20 25 30 35 40 45 50 55 60 65 0 10 20 30 40 50 radiant intensity(mw/sr) forward current(ma) 0 1 2 3 4 5 10 1 10 2 10 3 10 4 tp=100us tp/t=1/100 forward current(ma) forward voltage(v)
datasheet eaisv 3024 a 1 5 copyright ? 2010, everlight all ri ghts reserved. release date : jan . 0 6 .201 7 . issue no: dir - 0001387 rev.2 www.eve rlight.com relative light current vs. angular displacement
datasheet eaisv 3024 a 1 6 copyright ? 2010, everlight all ri ghts reserved. release date : jan . 0 6 .201 7 . issue no: dir - 0001387 rev.2 www.eve rlight.com precautions for use 1. over - current - proof customer must apply resistors for protection , otherwise slight voltage shift will cause big current change ( bu rn out will happen ). 2. storage 2.1 do not open moisture proof bag before the products are ready to use. 2.2 before opening the package, the leds should be kept at 30 or l ess and 90%rh or less. 2. 3 the leds should be used within a year. 2. 4 after opening the package, the leds should be kept at 30 or less and 6 0%rh or less. 2.5 the leds should be used within 168 hours (7 days) after opening the package 2.6 if the moi sture absorbent material (silica gel) has faded away or the leds have exceeded the storage time, baking treatment should be performed using the following conditions. baking treatment : 60 5 for min. 24 hours. 3. soldering condition 3.1 pb - free solder temper ature profile 3.2 reflow soldering should not be done more than two times. 3.3 when soldering, do not put stress on the leds during heating. 3.4 after soldering, do not warp the circuit board.
datasheet eaisv 3024 a 1 7 copyright ? 2010, everlight all ri ghts reserved. release date : jan . 0 6 .201 7 . issue no: dir - 0001387 rev.2 www.eve rlight.com 4. soldering iron each terminal is to go t o the tip of soldering iron temperature less than 350 for 3 seconds within once in less than the soldering iron capacity 25w. leave two seconds and more intervals, and do soldering of each terminal. be careful because the damage of the product is often started at the time of the hand solder. 5. repairing repair should not be done after the leds have been soldered. when repairing is unavoidable, a double - head soldering iron should be used (as below figure). it should be confirmed beforehand whether the characteristics of the leds will or will not be damage d by repairing.
datasheet eaisv 3024 a 1 8 copyright ? 2010, everlight all ri ghts reserved. release date : jan . 0 6 .201 7 . issue no: dir - 0001387 rev.2 www.eve rlight.com package dimensions note: the tolerances unless mentioned is 0.1mm ,unit = mm carrier tape dimensions: (q uantity : 15 00 pcs/ reel ) note: the tolerances unless mentioned is 0.1mm ,unit = mm
datasheet eaisv 3024 a 1 9 copyright ? 2010, everlight all ri ghts reserved. release date : jan . 0 6 .201 7 . issue no: dir - 0001387 rev.2 www.eve rlight.com packing procedure label form specification cpn: customers production number p/n : production number qty: packing quantity cat: ranks hue: peak wavelength ref: reference lot no: lot number made in taiwan: production place disclaimer 1. eve rlight reserves the right(s) on the adjustment of product material mix for the specification. 2. the product meets everlight published specification for a period of twelve (12) months from date of shipment. 3. the graphs shown in this datasheet are representing typical data only and do not show guaranteed values. 4. when using this product, please observe the absolute maximum ratings and the instructions for using outlined in these specification sheets. everlight assumes no responsibility for any damage resulting fr om the use of the product which does not comply with the absolute maximum ratings and the instructions included in these specification sheets. 5. these specification sheets include materials protected under copyright of everlight . reproduction in any form is prohibited without obtaining everlight s prior consent. 6. this product is not intended to be used for military, aircraft, automotive, medical, life sustaining or life saving applications or any other application which can result in human injury or death. ple ase contact authorized e verlight sales agent for special application request . aluminum moistue-proof bag label desiccant label xxxxxxxxxxxxxxxxxxxx xxxxxxxxxx xxxxxxxxxx - xxxxxxxxxx - xxxxxxxxxx xxxxxxxxxx xxxxxxxxxx btpyymmddxxxxx made in xxxxxx msl - x x
|
